Gravity: Analog Electrical Conductivity Sensor /Meter V2 (K=1)

DFRobot Gravity: analog electrical conductivity meter V2 is specially used to measure the electrical conductivity of an aqueous solution, and then to evaluate the water quality, which is often used in water culture, aquaculture, environmental water detection, and other fields.You may also check液体传感器Selection Guideto get better familiar with our liquid sensor series.

This ec meter product, as an upgraded version of the electrical conductivity meter V1, greatly improves the user experience and data precision. It supports 3~5v wide voltage input, and is compatible with 5V and 3.3V main control board; The output signal filtered by hardware has low jitters; The excitation source adopts AC signal, which effectively reduces the polarization effect, improves the precision, and prolongs the life of the probe; The software library uses two-point calibration method, and can automatically identify standard buffer solution, so simple and convenient.

With this product, the main control board (such asArduino), and the software library, you can quickly build an electrical conductivity meter, plug, and play, no welding. DFRobot provides a variety of water quality sensor products, uniform size, and interface, not only meet the needs of various water quality testing but also suitable for the DIY of multi-parameter water quality tester.

Conductivity is the reciprocal of the resistance, which is related to the ability of the material to carry the current. In the liquid, the reciprocal of the resistance, the conductivity, is the measure of its ability to conduct electricity. Conductivity is an important parameter of water quality. It can reflect the extent of electrolytes present in water.

Tips:
In order to ensure measurement accuracy, it is strongly recommended to add atemperature sensor测量温度,实现自动temperature compensation.DS18B20 waterproof temperature sensorcan also be used.

Attention:
1.The probe is a laboratory-grade probe. Do not immerse in liquid for a long time. Otherwise, this will shorten the life of the probe.
2.Platinum black layer is attached to the surface of the sheet metal in the probe. It should avoid any object touching it. It can only be washed with distilled water, otherwise, the platinum black layer will be damaged, resulting in an inaccurate measurement.

• 3.0~5.0V wide voltage input
• Hardware filtered output signal, low jitter
• AC excitation source, effectively reduce polarization
• Gravity connector and BNC connector, plug and play, no welding
• Software library supports two-point calibration and automatically identifies standard buffer solution, integrates temperature compensation algorithm
• Uniform size and connector, convenient for the design of mechanical structures

• Water quality monitoring.
• Aquaculture.
• Hydroponic & Aquaponic.

Signal Conversion Board (Transmitter) V2

• Supply Voltage: 3.0~5.0V
• Output Voltage: 0~3.4V
• Probe Connector: BNC
• Signal Connector: PH2.0-3Pin
• Measurement Accuracy: ±5% F.S.
• Board size: 42mm*32mm/1.65in*1.26in

Electrical Conductivity Probe

• Probe Type: Laboratory Grade
• Cell Constant: 1.0
• Support Detection Range: 0~20ms/cm
• Recommended Detection Range: 1~15ms/cm
• Temperature Range: 0~40°C
• Probe Life: >0.5 years (depending on the frequency of use)
• Cable Length: 100cm

Project 1.EC Meter with ESP32 and DFRobot EC module

Introduction:How to use DFRobot PH Meter module with an ESP32.

Project 2.Build KnowFlow: automatic water monitor

KnowFlowis the name of this water quality monitoring device, based on Arduino Uno. It can automatically monitor 5 parameters of water: pH, Temperature, Dissolved Oxygen, Electronic Conductivity, ORP.

• Central Control Unit:Arduino Uno(DFRobot Bluno在这种情况下)和扩张盾(DFRobot Expansion Shield V7.1in this case)
• Water Sensors: pH (pH probeand pH circuit board); EC (EC probeand EC circuit board); ORP (ORP probeand ORP circuit board); Temperature (temperature probeand temperature circuit board); Dissolved Oxygen (DO probe, BNC and circuit board);real-time clock circuit board
• Data Storage:Micro-SD module,Micro SD card
• Fit and fix: mounting plate, waterproof box( 200mm_150mm_75mm), waterproof joint
• Other parts:Cables (Wires),breadboard, bolts and nuts, screws, battery, double-sided adhesive, write on tape, small wrench, spiral cable wrap

• ec meter Product WiKi
• More ec meter Documents

• Electrical Conductivity Probe（K=1, Laboratory Grade） x1
• Signal Conversion Board (Transmitter) V2 x1
• Standard Buffer Solution 1413us/cm x2
• Standard Buffer Solution 12.88ms/cm x2
• Gravity Analog Sensor Cable x1
• Waterproof Gasket x2
• Screw Cap for BNC Connector x1
• M3 * 10 nylon pillar x4
• M3 * 5 screw x8